News
Central Laboratory of Technical Inspection (CLDT) - one of the largest and most modern testing laboratories in Poland is constantly developing
In current dynamic world, CLDT is expanding the spectrum of its activities to meet the expectations of the market and our customers. Today, our laboratories offer services with modern ultrasound testing techniques, i.e. TOFD (Time of Flight Diffraction), PAUT (Phased Array), TULA (TOFD Ultra Low Angle), which significantly facilitate the interpretation of the results obtained, increase the speed of testing and improve the quality of imaging. We are equipped with a Phased Array ultrasonic scanner (PAUT) for inspection of circumferential welds on small diameter pipes, as well as a Scorpion 2 inspection robot. In hard-to-reach areas and large area equipment (e.g., storage tanks), we perform visual inspections using UAVs (drones), which can also be equipped with thermal imaging cameras.
Our laboratories also offer testing by the PEC (Pulsed Eddy Current) method, which enables rapid thickness measurements of pipelines without removing thermal insulation, without the need for head coupling and without preparation of the test surface. Another test from our wide portfolio is vibration measurement by the optical motion amplification method. The use of a high-speed camera makes it possible to use every pixel in the recorded image as a measurement sensor.
Office of Technical Inspection (UDT) signs an agreement with the Civil Aviation Authority and the Military Aviation Authority
On 3rd of June 2024, an Agreement on cooperation in the field of qualification and certification of non-destructive testing personnel in aviation was signed by Adam Ogrodnik (Vice President of Office of Technical Inspection), Brig. Gen. Pil. Robert Cierniak (Chief of Military Aviation Authority) and Julian Rotter (Acting President of Civil Aviation Authority).This document defines the principles of operation of the National Non-Destructive Testing Certification System and the recognition by the President of the CAA and the Chief of the MAA National Commission for Non-Destructive Testing in Aviation within the meaning of point 3.22 of the Polish Standard PN-EN 4179.
The agreement replaces the previous one between UDT and CAA, which has been in force since 2013. Now, the Agreement has been joined by the MAA. Its scope is the result of experience gained and many years of cooperation between UDT and CAA in the field of qualification and certification of NDT personnel in aviation.
2006/42/WE, Badanie typu WE
OPIS
Ocena zgodności realizacjowana przez jednostkę notyfikowaną wg wymagań określonych w 2006/42/WE
CEL
Wystawienie Certyfikatu Zgodności dla Maszyny. Zlecający na tej podstawie mozę wystawić Deklarację Zgodności WE dla badanej maszyny.
DOKUMENTY ODNIESIENIA
- 2006/42/WE - Maszyny (MD)
- Rozporządzenie Ministra Gospodarki z dnia 21 października 2008 r. w sprawie zasadniczych wymagań dla maszyn
- Normy, przepisy lub wymagania firmy wskazane przez wnioskodawcę
GRUPY KLIENTÓW
- producent / upoważniony przedstawiciel, importer, dystrybutor, przekazujący do użytkowania, integrator, modernizujący, eksploatujący
DO KOGO SKIEROWANA JEST USŁUGA
Usługa skierowana do Klientów wytwarzających, sprowadzających na obszar EU, kompletujących, instalujących, maszyny i urządzenia stwarzające ryzyko upadku z wysokości większej niż 3m
ZASTOSOWANIE
Maszyny stwarzające ryzyko upadku z wysokości 3 metrów, podnośniki do serwisowania pojazdów, Jednostki logiczne wypełniające funkcje bezpieczeństwa, urządzenia ROPS i FOPS - ujęte w załączniku 4 DM 2006/42
DANE WEJŚCIOWE / DOKUMENTY WYMAGANE DO REALIZACJI USŁUGI
Dokumentacja techniczna maszyny określona przez zał. VII 2006/42/WE (Obliczenia, rysunki, opis, schematy elektryczne, hydrauliczne, pneumatyczne, instrukcje, analizy ryzyka, deklaracje maszyn bądź maszyn nieukończonych wchodzących w skład badanej maszyny ), wniosek wraz z podaniem wymagań odniesienia (norm zharmonizowanych np. EN 280, EN 1495)
ZAKRES CZYNNOŚCI
Zakres prac, wykonywanych przez ekspertów obejmuje:
- sprawdzenie poprawności i kompletności dokumentacji technicznej,
- sprawdzenie poprawności doboru wymagań odniesienia,
- opracowanie programu badań,
- wykonanie badań i prób zgodnie z programem badań
- ocenę wyników sprawdzeń, badań, prób technicznych i pomiarów,
- opracowanie dokumentów wyściowych: raportów ze sprawdzenia dokumentacji, sprawozdań/raportów z badań, certyfikatu badania typu WE.
DANE WYJŚCIOWE / DOKUMENTY
Certyfikat badania typu WE wraz z załącznikami
Raport ze sprawdzenia dokumentacji
Sprawozdanie/raport z badań zawierający:
- wyniki sprawdzeń, badań, prób technicznych i pomiarów
- o ile to właściwe stwierdzenie zgodności z wymaganiami dokumentów odniesienia
KORZYŚCI ZE ZREALIZOWANIA USŁUGI
Możliwość wystawienia Deklaracji Zgodności WE dzięki uzyskaniu certyfikatu badania typu WE. Uzyskanie przewagi konkurencyjnej.
News
Central Laboratory of Technical Inspection (CLDT) - one of the largest and most modern testing laboratories in Poland is constantly developing
In current dynamic world, CLDT is expanding the spectrum of its activities to meet the expectations of the market and our customers. Today, our laboratories offer services with modern ultrasound testing techniques, i.e. TOFD (Time of Flight Diffraction), PAUT (Phased Array), TULA (TOFD Ultra Low Angle), which significantly facilitate the interpretation of the results obtained, increase the speed of testing and improve the quality of imaging. We are equipped with a Phased Array ultrasonic scanner (PAUT) for inspection of circumferential welds on small diameter pipes, as well as a Scorpion 2 inspection robot. In hard-to-reach areas and large area equipment (e.g., storage tanks), we perform visual inspections using UAVs (drones), which can also be equipped with thermal imaging cameras.
Our laboratories also offer testing by the PEC (Pulsed Eddy Current) method, which enables rapid thickness measurements of pipelines without removing thermal insulation, without the need for head coupling and without preparation of the test surface. Another test from our wide portfolio is vibration measurement by the optical motion amplification method. The use of a high-speed camera makes it possible to use every pixel in the recorded image as a measurement sensor.
Office of Technical Inspection (UDT) signs an agreement with the Civil Aviation Authority and the Military Aviation Authority
On 3rd of June 2024, an Agreement on cooperation in the field of qualification and certification of non-destructive testing personnel in aviation was signed by Adam Ogrodnik (Vice President of Office of Technical Inspection), Brig. Gen. Pil. Robert Cierniak (Chief of Military Aviation Authority) and Julian Rotter (Acting President of Civil Aviation Authority).This document defines the principles of operation of the National Non-Destructive Testing Certification System and the recognition by the President of the CAA and the Chief of the MAA National Commission for Non-Destructive Testing in Aviation within the meaning of point 3.22 of the Polish Standard PN-EN 4179.
The agreement replaces the previous one between UDT and CAA, which has been in force since 2013. Now, the Agreement has been joined by the MAA. Its scope is the result of experience gained and many years of cooperation between UDT and CAA in the field of qualification and certification of NDT personnel in aviation.
Code of ethics
- With regard to the care for the appropriate image of UDT by directing the services provided to modern, professional and effective operation in the area of public safety while stimulating development and meeting the needs and expectations of customers, constantly striving to provide services in an ethical and competent manner a Code of Ethics, which is a set of ethical norms and behavioral patterns is being established.
- Compliance with accepted ethical standards and behavior patterns is crucial for strengthening the credibility of the UDT in society, to achieve the highest standards of customer service and strengthening employees' identification with the company and its values.
- All UDT staff members are obliged to comply with the UDT's internal regulations, which define the basic principles and good practices ensuring impartial and ethical activities.
Podkategorie
O nas
O nas
Współpraca
<!--[if !supportLists]-->1. <!--[endif]-->współpraca
Kariera
kariera
Polityka Jakości
POLITYKA JAKOŚCI, BHP i ŚRODOWISKOWA
Polityką Jakości Urzędu Dozoru Technicznego jest:
• Inicjowanie i prowadzenie działań służących zapewnieniu bezpieczeństwa eksploatacji urządzeń technicznych oraz ochrony środowiska zgodnie z wymaganiami zawartymi w następujących dokumentach: ustawa z dnia 21 grudnia 2000 r. o dozorze technicznym, PN-EN ISO/IEC 17020, PN-EN 45011, PN-EN ISO/IEC 17021, PN-EN ISO/IEC 17024, PN-EN ISO/IEC 17025.
• Ukierunkowanie świadczonych usług w zakresie:
- inspekcji,
- oceny zgodności,
- certyfikacji wyrobów,
- certyfikacji systemów zarządzania,
- certyfikacji osób,
- badań laboratoryjnych,
- wzorcowania wyposażenia pomiarowo-badawczego,
- popularyzowania zagadnień związanych z bezpieczeństwem technicznym,
- szkoleń
na spełnianie potrzeb i oczekiwań Klientów oraz wymagań mających zastosowanie przepisów.
• Dbałość o właściwy wizerunek UDT i świadczenie usług w sposób etyczny i kompetentny.
• Dostosowanie form działalności do wymagań rynku.
Zadowolenie Klientów stanowi miarę jakości naszych usług.
Podejmowanie działań na rzecz poprawy jakości ma dla nas znaczenie priorytetowe i wszyscy jesteśmy w nie zaangażowani.
Osiąganie planowanych wyników jakości realizujemy przez wdrożenie i ciągłe doskonalenie skuteczności systemu zarządzania jakością zgodnego z normą PN-EN ISO 9001.
Urząd Dozoru Technicznego inicjuje i prowadzi działania służące zapewnieniu bezpieczeństwa, ochrony zdrowia i życia pracowników, poprzez stałą poprawę i ciągłe doskonalenie bezpieczeństwa i higieny pracy, oraz ciągłe doskonalenie systemu zarządzania środowiskowego, przy spełnieniu wymagań prawnych i innych wymagań, zgodnie z PN-N-18001 oraz PN-EN ISO 14001.
Dążymy do:
• Zapobiegania wypadkom przy pracy, chorobom zawodowym, zdarzeniom potencjalnie wypadkowym oraz do identyfikacji zagrożeń i minimalizowania ryzyka zawodowego na stanowiskach pracy poprzez wprowadzenie kart oceny ryzyka zawodowego.
• Zminimalizowania negatywnego wpływu na środowisko, identyfikacji i kontroli znaczących aspektów środowiskowych, ograniczenia zużycia surowców naturalnych, energii elektrycznej, produkcji odpadów.
• Podnoszenia kwalifikacji oraz uwzględnienia roli pracowników i ich angażowania do działań na rzecz poprawy bhp i środowiska.
• Zapewnienia zasobów i środków do wdrażania polityki.
MarekWalczak
Prezes Prezes UDT
Warszawa, dnia 13 czerwca 2012 r.
Szkolenia
e-learning UDT
NOWOŚĆ!
Zapraszamy do udziału w szkoleniu e-learning Akademii UDT pt. Hakowi – Bezpieczna eksploatacja zawiesi
Program ramowy szkolenia e-learning obejmuje zagadnienia:
- Przepisy prawne
- Budowa zawiesi
- Parametry pracy
- Eksploatacja
- Zasady bezpiecznego podnoszenia
- Zakończenie - test sprawdzający
- Hakowi – wirtualny spacer
Przybliżony czas realizacji e-learningu to 4 godziny.
Uczestnik zgłoszony na e-learning otrzymuje dostęp do specjalnej platformy internetowej umożliwiającej samodzielną realizację szkolenia online w dogodnym terminie.
POBIERZ OFERTĘ I FORMULARZ ZGŁOSZENIOWY
Szczegóły i zgłoszenia:
Anna Parol Urząd Dozoru Technicznego Oddział Szczecin
tel. 91 48 06 412, kom. 883 375 929,
e-mail: anna.parol@udt.gov.pl